This specification2 relates to possible hazards that may not be recognized readily by the public and that may be encountered in the normal use for which a. ASTM F available in Chinese here: COMPS/htm. – Both F‐07e1 and F‐08 can be included as a. Both F ASTM F (PF) – Designation: F – 08 An American National Standard Standard Consumer Saf.
|Country:||Papua New Guinea|
|Published (Last):||16 January 2008|
|PDF File Size:||7.81 Mb|
|ePub File Size:||17.17 Mb|
|Price:||Free* [*Free Regsitration Required]|
Tests for Cleanliness and Preservative Effectiveness. A teether f963-80 meet this requirement when tested under the force only of its own weight and in a noncompressed state. However, the manufacturer or distributor must do enough testing to satisfy himself that normal use during the estimated lifetime of the toy is being simulated. Apply a 20 lbf 90 N to the cord so that the strain relief will ast stressed from any angle permitted by the construction of the toy.
Holes, Clearance, and Accessibility of Mechanisms Toys intended for children less than 48 months old shall not have accessible hazardous functional points. GTS is an experienced certification authority focusing on providing the third party inspection, identification, test and certification service.
For plastic bags, prepare by cutting the sides, without stretching, into two single sheets. The relevant tests for a type of toy can be performed in any order except where speci?
Recognizing f693-08 constraints, it is recommended, that where possible, such text begin on the next line below the signal word, and that a new line be used for each subsequent statement or separate thought. These requirements do not relate to the recognized and familiar hazards associated with the zstm clearances around the edges of doors or pivoted or hinged sections in toy truck bodies, toy earth moving machinery, and similar toys.
ASTM F (PF)_百度文库
NOTE 10—On multi-pole magnets use the area of the largest single pole, which can be determined using magnetic? This standard does not purport to address all of the safety concerns, if any, associated with its use.
It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the f—08 of regulatory limitations prior to use. Sound Producing Toys 6.
ASTM F Toy Safety Update
Such label shall remain legible after normal use and reasonably foreseeable abuse when tested in accordance with 8. It does not purport to cover every conceivable hazard f963-80 a particular toy. Possible entanglement or strangulation injury when attached to crib or playpen. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Battery compartments for button cell batteries are not subject to this requirement. NOTE 5—The latest issue of the regulation shall be used to determine compliance of the toy with the requirements of this speci?
Perform a total of three measurements. Yo-Yo Elastic Tether Toys: If a permanent partition or bars two or morewhich effectively limit the continuous space by making the largest internal dimension less than 6 in. Testing is performed using the recommended batteries installed.
Quiet periods longer than 15 s shall be excluded from the measurement period. This load shall be maintained for an additional 10 s. Keywords battery-operated toys; children; safety labeling; safety testing; toy safety requirements 39 Copyright by ASTM Int’l all rights reserved axtm Sun Feb 15 The tests shall be conducted in an expected use environment.
The values given in parentheses are for information only.
The impact area shall be at least 3 ft2 0. Powered models of aircraft, rockets, boats, and land vehicles; however, toys that are their counterparts are covered. C963-08 not leave child unattended while device is in use. Such an example is a sharp point necessary for the function of a needle. Active view current version of standard.
Radiated emission Conducted emission Electrostatic discharge immunity Radiated,Radio-frequency,Electromagnetic field immunity Electrical fast transient Surge immunity Radio disturbance and immunity Power frequency magnetic field immunity Voltage dips,Short interruptions and voltage variations immunity Harmonic current emissions Voltage fluctuations Conducted spurious emission Radiated spurious emission. Safety Labeling Requirements This revision also added: It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.