The wall dry–lining insulation shall be Kingspan Kooltherm® K Insulated Dry– lining Board comprising a mm plasterboard facing bonded to ____mm. Kingspan Kooltherm K Super high performance rigid thermoset phenolic insulation; Fibre-free, closed cell insulation core; 3-in-1 insulation, dry-lining and . Kooltherm K17 Insulated Dry-lining Board is an insulated plasterboard for traditional dot and daube plaster adhesive fixing. The tapered edge board enables flat.
|Published (Last):||11 January 2015|
|PDF File Size:||13.28 Mb|
|ePub File Size:||5.91 Mb|
|Price:||Free* [*Free Regsitration Required]|
The timbers should run vertically and be wide enough to offer a minimum 20 mm support to all four edges of the board. System R-values Click on the specific koolterm types below to view their System R-values.
These include the construction adhesive bonding method. Mechanical Fixing Directly to Masonry Substrates This method is for application to fair finished brick, block and concrete cavity walls where K17 is to be finished with gypsum plaster. Method of test for fire propagation for products Result – Fire propagation index of Fire kootlherm on building performance 1 not exceeding 12 and sub Index i1 not exceeding 6 for rigid phenolic insulation core.
Provision for horizontal services behind the board can be made by the use of two pieces of metal framing set no more than mm apart. The wall should be sound, dry and level as surface irregularities may impede fixing of the board.
Kingspan Kooltherm K17 should be screw fixed to each metal framing section with self drilling and tapping, countersunk, surface coated to avoid corrosionscrews placed at mm centres.
Method of test to determine the classification of the surface spread of flame of products Result – Class 1 rating. Ensure that the blobs adjacent to a board joint are approximately 25 mm in from the edge to avoid bridging the joint. Wallpaper should be stripped and surface mounted fittings removed.
Click Add to Cart Button. The boards are handled and fixed as with standard dot and dab plaster board methods. Koolthegm accurate trimming to achieve close-butting joints and continuity of insulation. Refer to fixing manufacturer instructions for more information. Tap the board back firmly using a straightedge, ensuring that the vertical edge is plumb.
Heavy surface mounted fittings will require provision for the fixing load to be applied direct to the supporting wall and not to the K17 in isolation. Ensure that safe methods of cleaning are used, as recommended by the suppliers of the spilt liquid.
mm Kingspan Kooltherm K17 Phenolic Insulation with Plasterboard
Test – BS —7: Apply 2 per board after the i17 has set, positioned 15 mm in from the board edge and at mid height with a nominal 25 mm embedment into the wall. These must be long enough kooltherrm allow a minimum 25 mm penetration of the supporting timber, and be placed not less than 10 mm from the edges kpoltherm the board and be spaced at mm intervals along all supporting timbers. Its durability depends on the supporting structure and the conditions of its use.
Kingspan Insulation New Kooltjerm We’re ready to help. Care should be taken to ensure that the cavity in cavity wall constructions is not bridged by the board or fixing medium in such a manner that would allow the passage of water through to the inner leaf. K17 may be used to line ceilings. Construction Adhesive Bonding View Instructions. The insulation core is resistant to short—term contact with petrol and with most dilute acids, alkalis and mineral oils. Block Wall mm View System R-value.
This method is for applications to brick, block or concrete masonry cavity walls.
Kooltherm K17 | Forman Building Systems
Care should be taken not to overdrive screws. Determination of compression behaviour. Installation is similar to that of standard plasterboard.
The reverse facing of K17 Insulated Plasterboard is a tissue based facing autohesively bonded to the insulation core during manufacture. The screws should be driven straight until the heads kioltherm slightly below the paper surface of the plasterboard facing.
Water Vapour Resistance Modified to include board facings, the boards achieve a resistance far greater than MN. This method may be used on timber frame constructions or on any dry masonry walls that will jooltherm and retain the battens and associated fixings.
Kingspan Kooltherm K17 Phenolic Insulated Plasterboard
It should, therefore, not be used to isolate dampness nor be used in continuously damp or humid conditions. Click on the specific application types below to view their System R-values.
A plaster skim finish can also be applied to the boards. Boards must always be placed with the long edge running across the joists, rafters or battens and all edges must be supported.
Mechanical Fixing to Metal Furring Systems K17 Insulated Plasterboard can be fixed by the use of proprietary metal framing systems to brick, block or concrete walls.
Timbers should be treated where appropriate. Send Us An Enquiry. The insulation core and facings used in the manufacture of K17 Insulated Plaster Board resist attack by mould and microbial growth and do not provide any food value to vermin.
The Reverse Face The reverse facing of K17 Insulated Plasterboard is a tissue based facing autohesively bonded koolthedm the insulation core during manufacture. As such, the will reflect light as well as heat, including ultraviolet light. The contribution of the product Total R-values depends on installation and environmental conditions.
Nailable plugs are recommended m17 complement the plaster dab bond. However, it is recommended that any spills be cleaned off fully before the boards are installed. Modified to include board facings, the boards achieve a resistance far greater than MN. On existing constructions all surfaces should be clean and free of loose or flaking materials.